Series HP – Form A-42
1. Click a link to view parts below or download a PDF Spec Sheet
2. Once you’ve found your part number and part name, request a parts quote
Preguntas? Inicie un chat
Jump to Assembly Parts and Manual Drawings
Click to enlarge
Download a PDF Spec Sheet
Frame Assembly
| Part # | Part Name |
|---|---|
| 1 | Manifold, Motor & Pump Assembly |
| 2 | Oil Sight Gage |
| 3 | Reservoir Cover |
| 4 | Gasket |
| 5 | Frame |
| 6 | Capscrew |
| 7 | Capscrew |
| 8 | Capscrew |
| 9 | L.H. Outside Gib |
| 10 | Gib Liner |
| 11 | Screw |
| 12 | L.H. Cylinder (R.H. Same) |
| 13 | Filler Block |
| 17 | Bed (Detachable Type) |
| 18 | Capscrew (With Detachable Type Bed Only) |
| 19 | Bolt (With Detachable Type Bed Only) |
| 20 | Bed Shoe Lock (With Detachable Type Bed Only) |
| 21 | Bed Shoe (With Detachable Type Bed Only) |
| 22 | Capscrew (With Detachable Type Bed Only) |
| 31 | R.H. Ram Liner |
| 32 | Ram |
| 33 | Safety Rail |
| 34 | Bolt |
| 35 | Pillow Block |
| 36 | Bolt |
| 37 | Center Ram Clamp Bars |
| 38 | Spring |
| 39 | End Ram Clamp Bars |
| 40 | R.H. Ram Liner |
| 41 | "T" Nut |
| 42 | Capscrew |
| 43 | Washer |
| 44 | Nut |
| 45 | Stud |
| 46 | Capscrew |
| 47 | Adjusting Block |
| 48 | Inner Pivot Block |
| 49 | Pivot Block Retainer |
| 50 | Washer |
| 51 | Bolt |
| 52 | Inner Pivot Shoe |
| 53 | Outer Pivot Shoe |
| 54 | Outer Pivot Block |
| 55 | Stud |
| 56 | Nut |
| 60 | Gib Liner |
| 61 | R.H. Outer Gib |
| 62 | Capscrew |
| 63 | Control Box |
| 64 | Washer |
| 65 | Bolt |
| 66 | Retaining Ring |
| 67 | Pin |
| 68 | Clevis (Clean Out) |
| 69 | "O" Ring (Cover Kit) |
| 70 | Inspection Door (Purchased) |
| 71 | Washer (As Assembly) |
| 72 | Bolt |
Click to enlarge
Linear Encoder Assembly
| Part # | Part Name |
|---|---|
| 1 | Frame (ref.) |
| 2 | Over-Travel Switch Bracket |
| 3 | Screw |
| 4 | Proximity Sensor |
| 5 | Rod End Bolt |
| 6 | Hex Nut |
| 7 | Roll Pin |
| 8 | Linear Encoder |
| 9 | Transducer Mounting Screw |
| 10 | Rail Guide |
| 11 | Rail Guide Mounting Screw |
| 12 | Screw |
| 13 | Scanning Head Support Guide |
| 14 | Screw |
| 15 | Spacer |
| 16 | Screw |
| 17 | Cable Support |
| 18 | Rod End with Grease Fitting |
| 19 | Hex Nut |
| 20 | Jam Nut |
| 21 | Threaded Rod |
| 22 | Encoder Bracket |
| 23 | Bracket Mounting Screw |
| 24 | Dowel Pin |
| 25 | Slide (ref.) |
Click to enlarge
Reservoir Cover Assembly
| Part # | Part Name |
|---|---|
| 1 | Reservoir Cover |
| 2 | Main Manifold Assembly |
| 3 | Front Manifold Mounting Block |
| 4 | Screw |
| 5 | Rear Manifold Mounting Block |
| 6 | Screw |
| 7 | Filler Strainer Unit |
| 8 | Screw |
| 9 | Filter |
| 10 | Screw |
| 11 | Pipe Coupling |
| 12 | Pipe |
| 13 | Gage |
| 14 | Gage Mounting Block |
| 15 | Pipe Spacer |
| 16 | Screw |
| 17 | Frame Cover |
| 18 | Oil Cooler |
| 19 | Spacer |
| 20 | Screw |
| 21 | Screw |
| 22 | Magnetic Plug |
| 23 | Motor |
| 24 | Motor Mounting Screw |
| 25 | Motor Mounting Bar |
| 26 | Bar Screw |
| 27 | Vibration Isolator |
| 28 | Single Pump (double pump with optional knockout) |
| 29 | Washer |
| 30 | Screw |
| 31 | Suction Flange |
| 32 | Screw |
| 33 | Suction cover |
| 34 | Screw |
| 35 | Pipe Flange |
| 36 | Screw |
| 37 | Temperature Sensor |
Click to enlarge
Pendent Arm Assembly
| Part # | Part Name |
|---|---|
| 1 | Control Box (ref.) |
| 2 | Gasket |
| 3 | Wire Stand Pipe |
| 4 | Screw |
| 5 | Lock Washer |
| 6 | Hex Nut |
| 7 | "V" Ring Seal |
| 8 | Lock Nuts |
| 9 | Pivot Bracket |
| 10 | Screw |
| 11 | Lock Washer |
| 12 | Set Screw |
| 13 | Hex Nut |
| 14 | Pendent Thrust Bearing |
| 15 | Screw |
| 16 | Pendent Arm |
| 17 | Coupling |
| 18 | Set Screw |
| 19 | Clamping Lever |
| 20 | Washer |
| 21 | Bearing |
| 22 | Capstan Nut |
| 23 | Operator Terminal |
| 24 | Pendent Stop |
| 25 | Bumper |
| 26 | Shim |
| 27 | Frame (ref.) |
Click to enlarge
HPS-110 Slide Assembly
| Part # | Part Name |
|---|---|
| 1 | Slide |
| 2 | Cylinder and Ball Enclosure (see separate part list) |
| 3 | Slide Liner |
| 4 | Screw |
| 5 | Slide Cover |
| 6 | Screw |
| 7 | Detector Switch Bracket |
| 8 | Bracket Screw |
| 9 | Roll Pin |
| 10 | Switch Mounting Plate |
| 11 | Plate Screw |
| 12 | Detector Switch Lever |
| 13 | Shoulder Bolt |
| 14 | Spring Plunger |
| 15 | Detector Switch |
| 16 | Switch Screw |
| 17 | Proximity Sensor* |
| 18 | Hex Nut* |
| 19 | Sensor Mounting Bracket* |
| 20 | Bracket Screw* |
| 21 | Hose Bracket* |
| 22 | Bracket Screw* |
| 23 | Junction Block* |
| 24 | Screw* |
*Optional
Click to enlarge
HPS-150 & 250 Slide Assembly
| Part # | Part Name |
|---|---|
| 1 | Slide |
| 2 | Cylinder Assembly (see separate part list) |
| 3 | Slider Assembly (see separate part list) |
| 4 | Hydraulic Cylinder |
| 5 | Knockout Cylinder Mounting Bracket |
| 6 | Screw |
| 7 | Screw |
| 8 | Clevis |
| 9 | Clevis Pin |
| 10 | Knockout Bar |
| 11 | Switch Bracket |
| 12 | Proximity Switch |
| 13 | Screw |
| 14 | Roll Pin |
| 15 | Wrist Pin |
| 16 | Retaining Ring |
| 17 | "O" Ring |
| 18 | "O" Ring |
| 19 | Wrist Pin Retainer |
| 20 | Screw |
| 21 | Slide Liner |
| 22 | Screw |
| 23 | Side Slide Cover |
| 24 | Screw |
| 25 | Front Slide Cover |
| 26 | Screw |
| 27 | Hose Bracket* |
| 28 | Bracket Screw* |
| 29 | Junction Block* |
| 30 | Screw* |
*Optional
Click to enlarge
HPS-110 Ball Seat
Note: Use this parts list for HPS-150 serial nos. P-53364 and lower
| Part # | Part Name |
|---|---|
| 1 | "V" Ring Seal |
| 2 | Ball Cap Enclosure |
| 3 | Screw |
| 4 | Stud |
| 5 | Hex Nut |
| 6 | Ball Cap |
| 7 | Piston Rod and Ball (ref.) |
| 8 | Ball Seat Shim |
| 9 | Ball Seat |
| 10 | Screw |
| 11 | Enclosure Shim |
| 12 | Ball Seat Wear Plate |
| 13 | Ball Seat Housing |
| 14 | "O" Ring |
| 15 | Ball Seat Base |
| 16 | Screw |
| 17 | Slide (ref.) |
| 18 | Hydraulic Cylinder* |
| 19 | Screw* |
| 20 | Rod End Coupling* |
| 21 | Screw* |
| 22 | Knockout Bar* |
*Optional
Click to enlarge
HPS-150 Cylinder Assembly
Note: Use this parts list for HPS-150 serial nos. P-53364 and lower
| Part # | Part Name |
|---|---|
| 1 | Slide (ref.) |
| 2 | Piston Rod Support |
| 3 | Screw |
| 4 | Piston Rod and Ball |
| 5 | Wiper Ring |
| 6 | Rod Seal |
| 7 | Rod Bearing |
| 8 | Lower Cylinder Cap |
| 9 | Screw |
| 10 | Lockwasher |
| 11 | "O" Ring |
| 12 | Lock Valve Manifold |
| 13 | Screw |
| 14 | "O" Ring |
| 15 | Cylinder Body |
| 16 | "O" Ring |
| 17 | Piston Bearing |
| 18 | Piston Seal |
| 19 | Screw* |
| 20 | Cylinder Assembly Cover* |
| 21 | Piston Assembly Stud* |
| 22 | Washer* |
| 23 | Hex Nut* |
*Warning: For use during cylinder
Click to enlarge
HPS-150 & 250 Slider Assembly
Note: HPS-150 serial nos. P-53364 and lower, use parts list on pages 44 and 45
| Part # | Part Name |
|---|---|
| 1 | Cylinder Assembly ( ref. ) |
| 2 | "V" Ring |
| 3 | Clip |
| 4 | Screw |
| 5 | Slider Enclosusre Top Plate |
| 6 | Screw |
| 7 | Slider Enclosure |
| 8 | R.H. Slider Enclosure End Plate |
| 9 | Screw |
| 10 | L.H. Slider Enclosure End Plate |
| 11 | Enclosure Front Plate |
| 12 | R.H. Slider Enclosure Seal |
| 13 | L.H. Slider Enclosure Seal |
| 14 | Upper Slider Liner |
| 15 | Screw |
| 16 | Lower Slider Liner |
| 17 | Slider |
| 18 | Spherical Bearing |
| 19 | Bearing Keeper |
| 20 | Screw |
| 21 | Slider Enclosure Base |
| 22 | Screw |
| 23 | Slide (ref.) |
Click to enlarge
HPS-110 Cylinder Assembly
Note: Use this parts list for HPS-150 serial nos. P-53364 and lower
| Part # | Part Name |
|---|---|
| 1 | Cylinder Assembly ( ref. ) |
| 2 | "V" Ring |
| 3 | Clip |
| 4 | Screw |
| 5 | Slider Enclosusre Top Plate |
| 6 | Screw |
| 7 | Slider Enclosure |
| 8 | R.H. Slider Enclosure End Plate |
| 9 | Screw |
| 10 | L.H. Slider Enclosure End Plate |
| 11 | Enclosure Front Plate |
| 12 | R.H. Slider Enclosure Seal |
| 13 | L.H. Slider Enclosure Seal |
| 14 | Upper Slider Liner |
| 15 | Screw |
| 16 | Lower Slider Liner |
| 17 | Slider |
| 18 | Spherical Bearing |
| 19 | Bearing Keeper |
| 20 | Screw |
| 21 | Slider Enclosure Base |
| 22 | Screw |
| 23 | Slide (ref.) |
